What type of material is C45?
medium carbon steel
C45 grade steel is a medium carbon steel offering moderate tensile strengths. The material is capable of through hardening by quenching and tempering on limited sections but can also be flame or induction hardened to Hrc 55.
What is C45 steel equivalent?
C45 grade steel is defined as a medium carbon steel offering tensile strengths in the modest range. Machinability of C45 is equivalent to that of mild steel for example CR1 grade, on the other hand weld ability is exhibited lower than that of mild steel.
What is C45 steel used for?
Quenched and subsequently tempered steel for C45 steel grade round bar, steel plate, flat and square is used for axles, bolts, forged connecting rods, crankshafts, torsion bars, light gears, guide rods, screws, forgings, wheel tyres, shafts, sickles, axes, knives, wood working drills, hammers, etc.
How hard is 45 steel?
Heat treatment and hardness Recommended tempering process specification: tempering temperature is 500~560℃, air cooling, hardness is 25~33HRC. The surface hardness of 45# steel is low after quenching and tempering, and it is not wear-resistant.
What material is S45C?
| JIS S45C Steel, Tempered | |
|---|---|
| Categories: | Metal; Ferrous Metal; Carbon Steel; AISI 1000 Series Steel; Medium Carbon Steel |
| Material Notes: | Very common grade in Asia. |
| Key Words: | Similar to AISI 1045 and DIN CK45. |
What is S45C material?
Can C45 be hardened?
C45 grade steel is a medium carbon steel offering moderate tensile strengths. The material is capable of through hardening by quenching and tempering on limited sections but can also be flame or induction hardened to Hrc 55. Machinability similar to that of mild steel can be expected, however weldability is reduced.
What is the hardness of C45 material?
C45 Steel Mechanical Properties
| Mechanical Properties | Metric | Imperial |
|---|---|---|
| Hardness, Rockwell B (Converted from Brinell hardness) | 84 | 84 |
| Hardness, Vickers (Converted from Brinell hardness) | 170 | 170 |
| Tensile Strength, Ultimate | 565 MPa | 81900 psi |
| Tensile Strength, Yield | 310 MPa | 45000 psi |
Which material is best for gears?
Thermoplastics are the best choice for gears where weight is the most important criteria. Gears made from plastics can be machined like metallic gears; however, some thermoplastics are better suited for manufacturing via injection molding. One of the most common injection molded thermoplastic is acetal.
What kind of steel is C45 in en?
EN 1.0503 steel is a carbon (non-alloy) steel formulated for primary forming into wrought products. Cited properties are appropriate for the normalized condition. 1.0503 is the EN numeric designation for this material. C45 is the EN chemical designation. It has a moderately low thermal conductivity among wrought carbon or non-alloy steels.
What should the tempering temperature of C45 steel be?
After welding, it’s better subjected to stress relief immediately, especially for large thickness weldments, the tempering temperature for stress relief is 550-660 °C. The heat treatment for C45 steel is mainly include quenching, tempering, normalizing and austenitizing, etc.
What kind of steel is in en 1.0503?
EN 1.0503 steel is a carbon (non-alloy) steel formulated for primary forming into wrought products. Cited properties are appropriate for the normalized condition. 1.0503 is the EN numeric designation for this material.
Which is better JIS s45c or DIN C45?
It also can be called JIS S45C and DIN C45 steel. It is usually used in normalized condition because of its bad hardenability. It needs to be quenching and tempering treatment to get higher mechanical performance.