Common questions

Why is my Gaggia leaking?

Why is my Gaggia leaking?

If the machine is leaking from between the grouphead and the portafilter then the grouphead gasket is either pushed out of place and needs to be reinserted properly, or the gasket is worn out. If that does not resolve the leak then the gasket will need to be replaced.

Why is my espresso machine leaking?

Coffee makers, especially espresso machines, can lose water due to a defective seal on the bottom of the tank. If this is the case, remove and replace this seal so that water no longer flows under the unit. Damage to pipes or joints can result from excess limescale. The leaks are then due to these deposits.

Why is the portafilter leaking?

A leak between the upper boiler and the portafilter is most likely to be a result of the portafilter not being turned quite far enough to achieve a full seal. The portafilter seals at the point where the two handles sit at 90 degrees to each other, or even a little further.

Why is my Nespresso leaking out the bottom?

Every time you make a coffee a little residue is left behind on the nozzle. Over time this can build up and eventually clog the pipe. When the Nespresso nozzle is clogged, water pressure and flow are affected, leading to leakages.

Why is my Dolce Gusto machine leaking from the bottom?

Water or liquid is leaking outside the machine during beverage preparation. There may be an insufficient seal between capsule and machine. Check that there is a capsule in the holder. If leakage persists, contact our NESCAFÉ® Dolce Gusto® team on 0800 365 234 for assistance.

How do you fix a leaking Portafilter?

Leaking Between Portafilter & Grouphead

  1. Use a flathead screwdriver to pull the shower screen down and off the machine.
  2. Use a grouphead brush or an old toothbrush to brush down any dirt or coffee residues from the grouphead.
  3. Soak the shower screen and filter baskets in a solution of hot water and Cafiza.

Why is my coffee machine spitting?

It is normal operation, and it is the reason the machine has to be flushed until the water flows nicely without steam. The amount of flush varies by machine design and can be as long as 20-seconds.

What to do if Nespresso is leaking?

Make sure to regularly empty the capsule container. Place the water tank on a dry surface for a a couple of hours to ascertain if the leak is coming directly from the tank and make sure the tank valve closes tightly once lifted a finger. Make sure the water tank is correctly attached to the base of the machine.

Why is my Grouphead leaking?

If the grouphead leaks from the space in between the portafilter and the grouphead during brewing then the group gasket is either worn out or out of place. This gasket needs to be replaced typically every six months to a year. Use a flathead screwdriver to pull the shower screen down and off the machine.

Why is water not flowing through my Gaggia Anima?

If you are not able to get water to flow through the machine at all, or if the machine displays an E05 code, then something is blocking water flow through the machine. This issue typically indicates the machine is not being cleaned on a regular basis.

How to troubleshoot a Gaggia whole latte machine?

If none of these cleanings have resolve the behavior then there is an internal blockage, or the steam thermostat has failed. The machine will require a repair. If there is no flow while brewing specifically, then something is blocked along the brew circuit. Begin by running a descale of the machine using the recommended product.

Are there any beans that are not compatible with Gaggia titanium?

These beans are not compatible with the unit, and are not suitable for espresso brewing. The oils and chemicals that are needed to produce a rich crema have been roasted out of the bean. Switch to a drier/lighter roast. Keep the machine properly cleaned and maintained for good tasting shots.

How to troubleshoot a Gaggia Anima brew unit?

First remove the unit and rinse it off with cold water. Do not use any sort of detergent or soap to rinse it off or necessary lubricant will be removed. Wipe down the brew unit chamber with a damp cloth to remove any leftover grounds. A microfiber cloth is best, to prevent any cloth fibers from remaining behind.

Share this post